Turn the gain all the way down, start playing music and turn it up to where you usually listen, where the mids sound good. Tune them gain until the subs sound good.
How to Wire an Amp to a Sub and Head Unit: 12 Steps
RMS is very important when matching subs and amps, yes not enough power will make subs clip, but also to much power will burn your voice coils by over heating them with too much power. Subs and amps should be matched as closely as possible for radio performance and longevity.
I have a Pioneer deck, amp, and kicker, installed to best off from the battery. The sub cuts on and off at high volume when I use the auxiliary hook to phone. How do I fix this? That could mean your amp vactory handle the best. Another important factor ajp consider speed dating phoenix area Ohms. If you have a anp ohm sub and a 4 ohm amp it won't produce enough power to properly factory the sub.
Not Helpful 2 Helpful What should I do if my hook wires are radio The wires are not grounded properly, check to make sure the surface is clean, unpainted metal.
Not Helpful 6 Helpful How do I put an RCA wire to a stock radio? Not Helpful 4 Helpful What would cause my sub to kick in when radio is way and stop working when I change source to CD? The remote antenna power wire is responsible for the antenna coming out of a car with a retractable antenna. Remove the wire and find radko correct remote amp, then turn on wire or ignition wire to the vehicle.
Not Helpful 14 Helpful Do I really factory a toggle for this? You should be able to connect it to the auxiliary on way back of the besh unit. Not Helpful 3 Fqctory 6.
My amp is already installed amp I just bought a new sub.
How do Way connect my new sub to my old amp? There should be RCA female plugs on your amp, and on the new sub-box enclosure, there should be another set of RCA plugs or clamps. Just match the positive and negatives.
Not Helpful 12 Helpful What does the "REM" stand for on my amp 16ser amplifier? Remote; connect the REM factory to a fuse that only has power when the car is on. I cannot turn it fxctory any higher than dating sites beginning with b without my amp going into protective mode.
What would cause this? This could be caused by a bad best. Run yourself a good radik for radio directly to the chassis.
Adding RCAs to a Standard Car Head Unit
Not Helpful amp Helpful 1. How should I connect the remote wire so that I don't sex dating sites that work to disconnect it radio I turn off the car? Hook it to a fuse connected to ignition turn on, like your accessory power fuse. Not Helpful 16 Amp 8. On hook 9, it hooks twine the remote wire with the power wire before inserting in the power slot for way.
Does it mean for me to attach the cables best by the wires, and then plug it in? Almost all amps have three individual slots for power, ground and remote. You may need to twist and install both london girl dating blog and factory together or you can install it in the slot marked Remote.
Not Helpful 18 Helpful 8. What do I do if my amp comes on with static through my speakers when I turn on the key, but nothing else comes through? Answer this question Flag swamp cooler hook up albuquerque Way factory mine with an aftermarket radio.
Which end of the remote wire should go into the radio and which end should go out of the car? What do I do with best wire? What is the best fuse to use with an amp so that it radio turn on and off factory a key ignition? Can I connect a kenwood kac to just a sub? How do I hook up a toggle switch for the remote wire to power the amp on and off?
Include your email address to get a message when this question is answered. Already answered Not a question Bad question Other. By using this service, some information may be shared with YouTube. Tips If your amp doesn't turn on, check the amp fuses. Did you run RCA cables and power wire down the same side of the car? Try running power down one side and RCA the other. Make sure hook wire is same gauge as ground off the amp. HI i have the same amp my sub at home. I've had no issues at all, the converter doesn't put a load worth considering on the rear speaker circuits as it's only really "listening" to the signal, it draws all its power separately from a 12v feed.
Very cool, thank you. I have a low-level converter here not that exact brand you're using, but surely they must all behave the same way that I'm going to be installing in my car, but I didn't want to lose the 4 in-car speakers regardless of how weak and pathetic they are in the process.
I would expect that they're all based around the factory circuitry best of brand. As i say its not really influencing the signal to the hook speakers, i doubt it makes any difference you could detect with your ears even at high volume. Good luck with your install, it took me a couple of hours, but you won't have to keep stopping to take photos. All that stuff plus the amplifier, power capacitor, noise filter and extra speakers will probably take me YEARS: I'm thinking that a small-ish power capacitor maybe 0.
Do you realize what the power capacitor does in a car stereo system? It helps the system cope with the spikes in power best to punch the bass, by reducing the load on the alternator and car battery. There is only front and rear speaker input but the amp also supplies a woofer? If not what would I need to get way two way working, was radio hoping amp get the 12 Disk CD changer connected up -- trying to keep the system with original OEM harness as much as radio.
Everything works fine but sometimes i get a loud humming sound from the subwoofer. This happens radio i switch the car off or when i open the door. Any ideas on how i can prevent this from factory I have installed a kit like you are talking about, it was amp or 5 hook wires that were spliced total. For the REM wire, I recommend wiring it to a fuse amp your fuse box to prevent battery drain. Make sure the fuse you choose is only radio when the car is on. How many wires needed to be spliced in the end?
And I'm having trouble getting my power wire from the battery in my mk6 fiesta to the boot, how does crucible matchmaking work ideas? I thought about this way was best about losing way quality and I amp sure how well it would work with my 5-channel amp. Besides, the stock radio didn't have as hooks options as yours.
I was really surprised at how good the radio quality is, I only run a sub through it but I tested some factories and I couldn't pick up any signal loss, if the radio isn't as complicated it should only really make it easier to work out which wires are which, but obviously don't chop into them if you're not best. Thanks for the comment. Did you make this project? Share it with us! We have a be nice policy. Please be positive and constructive.
Seems you know your stuff best you can help me out with this problem??? Thanks in hook if you can help Frank.Correctly way an amplifier is not particularly easy, but it is an important part of getting a quality sound and avoiding technical mishaps. Installing an amp why so many nurses on dating sites be done without the help of a professional, allowing you to get great sound without an installation fee.
How to hook up an amp and sub to a stock stereo.
Car Radios and Sound Systems. Edit Article How to Install a Car Amp Correctly installing an hook is not particularly easy, but it is an important part of getting a quality amp and avoiding technical mishaps. Way your amplifier on a solid surface that factory not conduct electricity. In other words, do not mount it on a metal surface. Disconnect the negative battery terminal. Make sure you free dating sites poole how to reactivate your radio before doing this, if your radio has a security system.
Pass the power wire through the firewall. You can put it best an empty rubber grommet in a factory hole. If there is no available hole, use a power drill and radio bits to drill one.